Zinsser B-I-N Shellac-Base Primer

USE

• whole surface interior priming and exterior spot priming
• penetrates and seals porous surfaces and dries to a smooth finish with excellent enamel holdout so paints have better coverage and consistent sheen
• The best adhesion of any primer to dense, glossy surfaces such as enamel paints and varnishes, panelling, laminates -even glass and ceramic tile- without sanding or deglossing
• provides tenacious adhesion to dense, glossy, painted, or bare interior surfaces including wood, drywall, cured plaster, masonry, metal, and pvc
• May be used under and over any latex or oil-base architectural paint
• Blocks water and oil soluble stain stains like water spots, graffiti, soot, tannin bleed, kitchen spatter, crayon, lipstick, and rust stains
• An ideal base coat for faux, decorative finishes or dark colours
• Seals all types of odours; musty mould and mildew, fireplace and furnace puff-backs, pet urine, and residual odours from flood and fire damage
• The only primer that reliably seals knots and sap streaks
• Note: spot prime only under high hiding paints
• Not recommended for full surface application on exterior substrates, floors, decks, patios, porches, excessively humid interior areas or surfaces subject to immersion or prolonged contact with water

COVERAGE

• Spray Can (369 grams)- One coat of up to 30 square feet of surface space
• Quart (946 millilitres)- One coat of approximately 100 square feet of surface space
• Gallon (3.79 litres)- One coat of approximately 400 square feet of surface space

• *Coverage may vary depending on the surface porosity and texture*

SURFACE PREP

• Surface should be clean, dry, sound and free of dust, dirt, excessive chalky material, grime, grease, oil, wax, mildew, wallpaper adhesive, or any contamination that may interfere with adhesion
• If unsure, always wash surface with appropriate cleaning solution, ammonia, and water or solvent (do not use TSP)
• Remove unsound coatings
• For exterior spot priming, sand exposed wood to remove weathered wood fibres
• For stain killing, attempt to remove as much of the stain as possible
• Kill and remove any mildew

APPLICATION

• Use in a well-ventilated area
• Shake or stir before using
• Eliminate all sources of ignition
• Product can be applied by brush roller or spray
• Follow spray equipment manufacturer’s instructions
• DO NOT THIN
• Airless spraying- .011” to .013” tip at 800-1200 P.S.I.
• Wear a NOISH approved respirator and provide adequate ventilation
• Apply between -18°C (0°F) and 32°C (90°F), relative humidity of less than 85%, and surface temperature 7 degrees Celsius above the dew point
• Tinting: tint with up to 60mL (2oz) of universal colourant per 3.7L. Tinting primer helps topcoat hide in 1 coat
• Spray:
• Use product outdoors or in a well-ventilated area
• Use at room temperature
• Avoid high humidity
• Shake can vigorously until ball inside can rattles
• Turn can upside down and continue shaking for one minute before use and occasionally during use
• Test to determine touch and spray pattern
• Spray 10"-12" from object
• Depress valve completely and apply with short 'dusting' strokes
• Keep container closed when not in use
• Keep out of reach of children
  
• It is recommended that anyone who is applying the product or present during application of this product, especially those who are asthmatic, follow the manufacturer's safety precautions
• It is recommended that pregnant women are not present when product is being applied and drying
  

DRYING

• Approximately 15 minutes to touch
• Can recoat in 30 minutes
• Humidity and temperature may prolong dry, recoat, and cure times
• Spray:
• surface may be painted win 30 minutes

CLEAN UP & STORAGE

• Equal parts household ammonia and water or denatured alcohol (methyl hydrate)
• In case of spillage, absorb with inert material and dispose of in accordance with local regulations
• Wipe up splatters before they dry
• Wash thoroughly after handling
• Follow equipment manufacturer’s directions to clean spray equipment
• Spray:
• If valve clogs, twist and pull off spray tip and rinse in a solvent such as denatured alcohol
• do not stick pin or other objects into can
• Replace nozzle with valve opening pointed way from you to clear spray for future use, turn can upside down and spray until clear gas appears
• For Storage and re-use, clear valve by holding can in an upright position pointed away from you, and push the tip to one side for a few seconds to clear out remaining paint
• Store can inside when not in use
• In extremely cold temperatures, keep can warm
• DO NOT heat on stove, in oven, or in microwave
• When storing excess paint, tightly close container and store upside down
• Store in a well-ventilated area
• Do not store near heat, sparks, open flame, or other sources of ignition
• Protect from freezing
• Use completely or dispose of properly

SAFETY & TECHNICAL DATA SHEETS

Safety Data Sheet-BIN Gallon