Benjamin Moore ARBORCOAT Classic Oil Exterior Stain- Translucent (K326)

USE

• Ideal for use on decking, siding, fencing, shakes, and furniture
• For application on exterior hardwoods such as mahogany, teak, and ipe as well as traditional woods like pine, cedar, and redwood
• Not recommended for use on previously painted surfaces, abraded, or brushed plywood

COVERAGE

• Gallon (3.79 litres)- One coat of approximately 200-350 square feet of surface space
• Coverage depends on surface porosity and texture
• Be sure to estimate the right amount of stain for the job
• This will ensure colour uniformity and minimize the disposal of excess stain
• Prior to staining, make sure to have enough stain to complete an entire section
• *Coverage may vary depending on the type, age, and texture of substrate as well as the application method*

SURFACE PREP

• Surfaces to be stained must be clean, dry, and free of dirt, mildew, oil, or grease
• Remove contaminants or chalky residue from weathered stained surfaces by washing with Multi purpose cleaner (K318)
• This product can also be applied to surfaces previously stained with a translucent or semi-transparent stain that is weathered but is not flaking or peeling
• Smooth planed wood must be sanded thoroughly or treated with a brighter & neutralizer (K317) to break the “mill glaze” to allow proper penetration and adhesion
• If the existing coating is a solid stain or paint it should be completely removed prior to finishing with a finish remover (K315)
• Weathered wood and mildew:
  • prior to staining, weathered wood must be sanded or treated with a wood restorer (K316), following directions, until a sound surface is obtained (loose or damaged wood fibres removed)
  • If mildew is evident, it must be removed by scrubbing with a restorer (K316) prior to staining or it will continue to grow through the fresh new stain
  • If mildew is widespread, the use of power wash spray equipment is suggested
  • Particular attention should be paid to overhead surfaces such as eaves, ceilings, and overhangs
• Unweathered areas such as eaves, ceilings, or overhangs must be washed with a detergent solution and/or rinsed with a strong stream from a garden hose to remove surface salts that can interfere with proper adhesion

APPLICATION

• Always test a small area for colour, penetration, and drying before proceeding
• DO NOT THIN
• Stir thoroughly before and occasionally during use
• Brushing is the preferred method of application
• When applied by roller or spray, back brushing is recommended to ensure a uniform distribution
• Do not over apply, excessive or uneven application will prolong the dry time and may result in sheen irregularity
• If needed, a second coat of stain can be applied at a rate of no less than 46.5-55.7 square metres (500-600 square feet) per 3.79L
• Wait for the first cost to dry 24-48 hours before applying the second coat
• Please note that multiple coats will affect the opacity of the final finish and obscure more of the natural colour of the wood
• Multiple coats may also cause the finish to have a slight sheen
• This sheen will slowly decrease with normal weathering
• Use product when surface temperature is above 4.4°C (40°F)
• Do not apply in direct sunlight
• Keep container closed when not in use
• Keep out of reach of children
• It is recommended that anyone who is applying the product or present during application of this product, especially those who are asthmatic, follow the manufacturer's safety precautions
• It is recommended that pregnant women are not present when product is being applied and drying
  

DRYING

• Dries to touch in 6-8 hours
• Can be recoated after 24-48 hours
• Decks: allow 5-7 days for the stain to fully cure before full return to service
• Humidity, temperature, and altitude may prolong dry, recoat, and cure times

CLEAN UP & STORAGE

• Clean brushes and equipment with mineral spirits
• In case of spillage, absorb with inert material and dispose of in accordance with local regulations
• Wash thoroughly after handling
  
• When storing, tightly close container and store upside down
• Store in a well-ventilated area
• Do not store near heat, sparks, open flame, or other sources of ignition
• Protect from freezing
  
• Use completely or dispose of properly

SAFETY & TECHNICAL DATA SHEETS

Safety Data Sheet-Silver Gray (K326-70)

Technical Data Sheet (K326)